|
About the developement category
|
|
0
|
517
|
June 8, 2020
|
|
Help getting started / basics!
|
|
2
|
33
|
October 1, 2025
|
|
Regenerative Braking
|
|
102
|
6741
|
September 28, 2025
|
|
MosquiNo - Yukon concept
|
|
31
|
548
|
September 22, 2025
|
|
Encoder Alignment
|
|
1
|
24
|
September 18, 2025
|
|
SimpleFOC stepstick
|
|
58
|
1726
|
September 11, 2025
|
|
Porting to STM32F302CCT6 with DRV8323R
|
|
1
|
45
|
August 28, 2025
|
|
"Failed to detect movement" during motor initialization - but sensor angle changes when turning by hand
|
|
2
|
44
|
August 26, 2025
|
|
Help needed - ESP32 C2/3/6 analogRead execution time
|
|
2
|
46
|
August 21, 2025
|
|
Unsigned long _micros()
|
|
1
|
22
|
August 20, 2025
|
|
Help needed - ESP32S3 analogRead execution time 🙋
|
|
6
|
1899
|
July 28, 2025
|
|
BLDC motor closed loop problem
|
|
0
|
58
|
July 25, 2025
|
|
Haptic Feedback and LVGL
|
|
3
|
79
|
July 23, 2025
|
|
B-G431B-ESC1 + Platform IO : help needed on soft : not driving
|
|
9
|
59
|
July 21, 2025
|
|
Espressif port of simplefoc
|
|
4
|
751
|
July 20, 2025
|
|
DC Motor position control does not work below 0 angle
|
|
3
|
36
|
July 20, 2025
|
|
Esp32s3 qtpy platformio SPI problem
|
|
3
|
59
|
July 20, 2025
|
|
initFOC failing while using find_sensor_offset_and_direction
|
|
1
|
35
|
July 13, 2025
|
|
IR2110 High-Side Output Shows Voltage When Idle
|
|
1
|
33
|
July 13, 2025
|
|
Security Considerations in Motor Control Firmware – Am I Overthinking It?
|
|
2
|
47
|
July 13, 2025
|
|
The motor reverses direction when holding the torque.
|
|
0
|
31
|
July 9, 2025
|
|
Autodetect of motor
|
|
1
|
46
|
July 9, 2025
|
|
Low side current sensing for stepper motors
|
|
39
|
458
|
July 8, 2025
|
|
FOC Init Fails with iPower GM6208 (28 poles) + AMT103 Encoder + STM32 Nucleo F446RE
|
|
1
|
52
|
July 2, 2025
|
|
Feature request: add klipper MCU input mode
|
|
32
|
2582
|
July 1, 2025
|
|
Gimbal motor losing control
|
|
1
|
491
|
June 26, 2025
|
|
Problems in Increasing Speed in FPGA based FOC Implementation
|
|
0
|
47
|
June 23, 2025
|
|
Help tuning GBM4108-120T with some load/inertia (central motor in setup)
|
|
2
|
76
|
June 21, 2025
|
|
Haptic Wheels for Gimbal Control
|
|
0
|
35
|
June 9, 2025
|
|
Seeking Help: Motor moving one full rotation during initFOC() and then stopping permanently
|
|
1
|
51
|
June 8, 2025
|