# SIMPLEFOC MINI (my version) - 3/3 available
**URL:** https://community.simplefoc.com/t/simplefoc-mini-my-version-3-3-available/7612
**Category:** giveaway
**Created:** [August 27, 2025, 12:04pm UTC](https://community.simplefoc.com/t/simplefoc-mini-my-version-3-3-available/7612 "2025-08-27T12:04:10Z")
**Posts on this page:** 13
**Page:** 1
### Author:  [@rew](https://community.simplefoc.com/u/rew)
#### Post date: [August 27, 2025, 12:04pm UTC](https://community.simplefoc.com/t/simplefoc-mini-my-version-3-3-available/7612/1 "2025-08-27T12:04:10Z")
My version of “simplefoc mini” Plan is: you get the through-hole parts in the bag but not soldered. You pay shipping EUR 5 (about $6).
---
### Author:  [@gimbal\_pete](https://community.simplefoc.com/u/gimbal_pete)
#### Post date: [September 2, 2025, 4:27pm UTC](https://community.simplefoc.com/t/simplefoc-mini-my-version-3-3-available/7612/2 "2025-09-02T16:27:53Z")
How come you used the DRV8313 and not the DRV8316 as per Anton’s latest revision?
> [@SimpleFOCMini v2.1](https://community.simplefoc.com/t/simplefocmini-v2-1/7113):
>
> Hi guys, I’ve recently done another iteration of the mini board, and I’ve decided to go for the DRV8316 chip this time. As it already has low-side current sensing and a bit better current capacity than DRV8313 or LAN9252 its a great candidate for a minimal starter-kit type of boards. I’ve done a few iterations and the results are pretty good. Here is the comparison to the mini v1.1 Info Mini v2 Mini v1 Driver DRV8316CT - [datasheet](https://www.ti.com/lit/ds/symlink/drv8316.pdf) CT version of the DRV8316 with Hardware co…
---
### Author:  [@rew](https://community.simplefoc.com/u/rew)
#### Post date: [September 2, 2025, 5:04pm UTC](https://community.simplefoc.com/t/simplefoc-mini-my-version-3-3-available/7612/3 "2025-09-02T17:04:50Z")
I didn’t see that message or know about that chip. The 5x better RDSON sounds attractive! Next iteration I’ll do that. So for now these are relatively low-current.
---
### Author:  [@gimbal\_pete](https://community.simplefoc.com/u/gimbal_pete)
#### Post date: [September 2, 2025, 5:41pm UTC](https://community.simplefoc.com/t/simplefoc-mini-my-version-3-3-available/7612/4 "2025-09-02T17:41:22Z")
I looked at the datasheets and it looks more like 2.5-3x lower (0.25 vs 0.095).
---
### Author:  [@rew](https://community.simplefoc.com/u/rew)
#### Post date: [September 2, 2025, 6:19pm UTC](https://community.simplefoc.com/t/simplefoc-mini-my-version-3-3-available/7612/5 "2025-09-02T18:19:38Z")
The datasheets specify them in different ways. One specifies two RDSON resistances on the order of 0.25 separately and the other specifies 100mOhm for both together.
That last one is “easier” as all current flowing through a high-side mosfet will eventually come back and also flow through the lowside as well. So if you have 100mOhm of total resistance and want to use 2A, you can calculate 2A _x 100mOhm = 200mV. So power loss is 2A x 200mV = 400mW. For the 8313 datsheet you first have to add up the resistances._
---
### Author:  [@gimbal\_pete](https://community.simplefoc.com/u/gimbal_pete)
#### Post date: [September 2, 2025, 7:35pm UTC](https://community.simplefoc.com/t/simplefoc-mini-my-version-3-3-available/7612/6 "2025-09-02T19:35:03Z")
Really interesting to know, thanks.
---
### Author:  [@peepo](https://community.simplefoc.com/u/peepo)
#### Post date: [October 9, 2025, 5:56pm UTC](https://community.simplefoc.com/t/simplefoc-mini-my-version-3-3-available/7612/7 "2025-10-09T17:56:47Z")
I could definitely use these, sent email, via bitwizard.nl
---
### Author:  [@rew](https://community.simplefoc.com/u/rew)
#### Post date: [October 21, 2025, 9:12am UTC](https://community.simplefoc.com/t/simplefoc-mini-my-version-3-3-available/7612/8 "2025-10-21T09:12:33Z")
Peepo got his. two left. (I forgot to mention: 1 per person, which surprised peepo a bit.)
---
### Author:  [@Felipegalind0](https://community.simplefoc.com/u/Felipegalind0)
#### Post date: [October 22, 2025, 1:12am UTC](https://community.simplefoc.com/t/simplefoc-mini-my-version-3-3-available/7612/9 "2025-10-22T01:12:34Z")
Any chance I could get one?
---
### Author:  [@rew](https://community.simplefoc.com/u/rew)
#### Post date: [October 24, 2025, 7:35pm UTC](https://community.simplefoc.com/t/simplefoc-mini-my-version-3-3-available/7612/10 "2025-10-24T19:35:00Z")
You really need to reply to the PM I sent or figure out my email like peepo did. I can’t start guessing your shipping address.
---
### Author:  [@runger](https://community.simplefoc.com/u/runger)
#### Post date: [October 29, 2025, 2:28pm UTC](https://community.simplefoc.com/t/simplefoc-mini-my-version-3-3-available/7612/11 "2025-10-29T14:28:29Z")
The DM feature in discourse forum can be a bit hard to find. If you click on your user icon at the top-right and then on the “envelope” icon in the menu that opens you will see your DMs.
To send a new DM just tap on a user and tap the “Message” button in the popup.
---
### Author:  [@Cole\_Herber](https://community.simplefoc.com/u/Cole_Herber)
#### Post date: [November 16, 2025, 7:46am UTC](https://community.simplefoc.com/t/simplefoc-mini-my-version-3-3-available/7612/12 "2025-11-16T07:46:14Z")
Is there a chance you have one left?
---
### Author:  [@rew](https://community.simplefoc.com/u/rew)
#### Post date: [November 16, 2025, 8:49am UTC](https://community.simplefoc.com/t/simplefoc-mini-my-version-3-3-available/7612/13 "2025-11-16T08:49:12Z")
Yup! Felipe gave up trying to send me his address….